NMEA Multiplexer with bidirectional SeaTalk port and USB

238.00€

gadgetPool
NMEA Multiplexer with bidirectional SeaTalk and USB Port

The gadgetPool NMEA & SeaTalk Multiplexer is a NMEA-Multiplexer with additional Seatalk port and USB-port.
With this NMEA-Multiplexer you can connect serveral NMEA devices, read data from a SeaTalk network, write Data to your Seatalk network and also connect your PC

  

Multiplexer ports :

  • 4 galvanic isolated NMEA 0183 inputs.
  • 2 NMEA 0183 outputs
  • 1 galvanic isolated SeaTalk port. SeaTalk Data are translated into NMEA sentences, NMEA Data are translated into Seatalk data
  • 1 USB port for PC. With the USB port, a PC can send and receive NMEA Data.

What is a Nmea-Multipelxer good for ?

NMEA devices can send data and/or receive data from other NMEA devices. .

According to NMEA standards, a sender can send it's data to up to 4 receivers.

For a receiver, It is not possible to receive data from more than one sender.
A NMEA receiver can only receive data from one other device at a time.
I.e. With one NMEA input port, a Chart plotter can not receive position from a GPS device and depth data from a depth sounder at the same time.

In order to be able to receive data from more than one NMEA source, a NMEA-Multiplexer has to be placed in between the senders and the receiver.

A NMEA-Multiplexer receives data on separated input ports from different NMEA devices.
It buffers this incoming data, filters them and sends them out well ordered to the receiver.

gadgetPool NMEA-Multiplexer can receive data from :

  • up to 4 NMEA devices ( i.e. GPS, depth sounder, wind instruments, AIS etc.. )
  • 1 board PC via USB
  • 1 SeaTalk network.

The Multiplexer buffers, filters and send this data in proper order to :

  • 1 board PC via USB
  • up to 4 different types of NMEA receivers
  • to the Seatalk network

Housing and terminals

Housing
The multiplexer comes in a nice and sturdy metal housing.
For easy installation and service, all terminals for NMEA, SeaTalk and power supply are detachable

NMEA inputs


NMEA outputs


Update : In the picture above only two NMEA out ports are shown. Meanwhile all 4 NMEA out ports are available.

SeaTalk connection

Currently the following NMEA sentences can be produced based on incoming SeaTalk data:

  • $IIDBT Depth
  • $IIVHW Speed through water
  • $IIMTW Water temperature
  • $IIVLW Total milage, trip milage
  • $IIMWV Wind direction and wind speed
  • $IIHDM Heading magnetic
  • $IIRMC Speed over ground,heading, longitude, latitude , time, date
    Optional an aditional $IIGLL sentence can be sent.
  • $IIRSA Rudder

Power supply

Technical data :

  • Operation voltage : 10-30 Volt DC.
  • Power consumption : 60 mA ( 100 mA max. at full load)
  • Inputs : 4 * NMEA-0183 ( RS-422 ) galvanic isolated
  • Outputs : 4 * NMEA-0183 ( RS-422 )
  • Network : 1 * SeaTalk in/output galvanic isolated
  • Baudrates : 1200 Baud - 38400 Baud ( USB up to 57600 Baud )
  • Memory : 2*4 kB Buffer for each NMEA channel. ( 4kB send/ 4kB receive)
  • PC-interface : 1 * USB virtual serial port for NMEA sending and receiving



Parse Time: 0.134s